Athens Water Heater Safety Precautions

Posted by on Sep 22, 2014 in Plumbing Repair Athens GA, Water Heater Repair Athens GA

Effectively maintaining ones water heater is crucial not simply so it works to its full capacity and can save some energy money, but for safety issues too. Yes, it can blow up – it doesn’t occur too typically for property owners, but undoubtedly this is something that Water Heater Repair Athens GA does not wish to have occur to you!

Vents
Venting can be type of technical however we will go over the essentials here. The vent need to be the same diameter as the draft diverter of the water heater tank. It is expected to increase and out (for atmospherically vented heaters). Not other directs like up, down, up and out. For direct-vent water heaters, the vent ought to head out a side wall. When it comes to power-vent heaters, the fan blows the fumes out, so there is some versatility in the direction they are vented.

Any roofing system or wall that the vent goes through need to be a double wall. The single wall pass throughs must be screwed with three screws per area. If these essentials are not followed, the vents can fall apart in time and carbon monoxide gas can cause major problems within ones house. Obviously we don’t want that to take place!

The only other interested in ventilation is that of backdrafting. The fumes can consume the vents with acid condensation. If enough of this gets on cold piping and the water heater it will not be a great circumstance for a properly working water heater. If the fumes go back inside the rather of being appropriately vented outside, the fumes can get in the living locations of the home. Soot issues can occur too.

Dielectric Connectors
The steel water heater is connected to cooper pipes by the dielectric connectors. When two these two metals are assembled in water electrolysis happens. The procedure rusts one metal away to secure the other. This process is important in shielding the inside of the water heater. Inspection for leakages must be done where the connections are made.

Temperature and Pressure Relief Valve
This is kinda of a crucial part of the water heater, for it helps ensure the darn thing does not blow up under pressure if the temperature goes beyond the proper limits the water heater is developed for. Once a year (at least) theĀ T&P valve should be examined to make certain, it is working correctly, for they can be vulnerable to failure. Simply pulling up on the handle water needs to stream easily out and stop when the handle is released. If it simply runs or drips, or does nothing at all, it will should be replaced.

The drain lines for the T&P line ought to not be directed up, because water does not stream uphill too well. Ensure it goes down and or out please. If water is running out the drain line regularly, it is the indicator of something incorrect too. It could be among a number of different things that we will not enter into below – simply speak to a regional plumbing technician please.

Earthquake Straps
Yep, even if you do not reside in an earthquake area and are needed to have these on ones water heater, it is a great idea to do so. It appears like many all new houses in sub-divisions nowadays have the water heater in the garage. Yes, there is typically a concrete curb in front of it so one does not drive a vehicle into it, however things can unintentionally knock it over so be safe and strap that say thanks to in.

Temperature Level Setting
It appears most domestic water heater tanks have settings of warm – hot – really hot … and not degree markings. Some “pointers” on conserving energy in the house specifically in the winter season time, say to reduce the setting on the tank to 120 degrees. That’s excellent for conserving energy but legionella germs, which causes Legionnaire’s condition can grow at 120 degrees. By inhaling the mist from the water in the shower, one can inhale the bacteria. Look for a medium between 130 and 120 degrees. Above 130 degrees is technically a scalding temperature level so be mindful.

Anode Rods
These generally are made of aluminum and there is absolutely nothing incorrect with that in theory, though we suggest utilizing magnesium ones. Let’s say for whatever reason there is some kind of emergency or catastrophe where one lives and one needed to utilize the water in the water heater for drinking water (since lots of emergency preparedness people encourage doing this). The water that comes out of the drain valve is the water at the bottom of the tank. If one has aluminum anodes, that water will be loaded with aluminum substances, which is not great for the body. It is bad for the stomach, intestinal tract and joints.

The anodes help with rust defense and are essential in prolonging the life of the water heater. They can also assist with odor troubles with the water. Generally, magnesium anodes simply work much better for a great deal of different reasons like the wellness perks, let develop up of sediment, a quieter water heater, and they often work much better with softened water.

Drain Valve
Ok, simply inspect it at least yearly to make sure the darn thing opens and works. And it is excellent to drain and purge the tank a minimum of once a year anyhow (something you naturally are doing already). If for some reason one should use the water throughout a catastrophe or drain it to rather a loud tank and have actually not drained it routinely, and it does not open, it will take longer to correct the problem you are at first trying to fix.

Combustion Changer Hatch
Because gas and oil water heaters breathe the air drawn in from below, combust with it and exhale it, it is important to keep the area around it, specifically beneath the water heater, clean and swept. If if is not burning effectively, it can trigger preparing problems (pointed out above), as well as combustion and fume issues and possibly be a fire danger. Some of examining the chamber and exactly how the flame burns is objective so we are not going to go into a lot of detail below. it is crucial to see if the combustion chamber roof has a lot of rust or water markings or is black in color. These are not an excellent indicator at all. One ought to see some blue flame at the bottom when it burns and orange and yellow at the top, however, the yellow should not be extremely high up. One need to see gray metal, some white condensation marks are ok.

Here is an infographic to highlight the information above:

Water Heater Repair Athens GA